8.1.5.6 Blu-ray creator fails with CUDA

[Tamyac]

Hi,

There was no 8.1.5.6 forums on the prefix, so I picked general. Hope that's ok

I tried to convert a mkv and it failed with error 504. I turned off CUDA and it's now going ok.

Is is ok to report errors with CUDA, or should we just turn it off and not worry about reporting any problems?

process_log:

You are going to try "Blu-ray Creator" option.: 21:02:46
Conversion: one pass: 21:02:47
CUDA GPU acceleration for video decoding enabled
: 21:02:47
CUDA GPU acceleration for video encoding enabled
: 21:02:47
Work 0 failed, Error = 504.00 0 error: filter name(filter_vdecode), type(2), id(1), get module_error(502.04 7 706 13)

: 21:02:50

thanks
Tanya

[terry5]

Hi Tamyac,
Please update your fab to the lastest build 8161 and try it again. If failed, please post the internal log here. Thanks.

[mrmf75]

cuda-dvd creator 8161

i have same problem with cuda,i'm using 8161 dvd creator.?

[fraroy]

Hello,

I also have same problem with blu-ray creator and cuda. You will find below an extract of the internal log. The source file is a .mp4 at 1080. Note there is a warning in the log about the bitrate being too big. How can I get blu-ray creator to work ?

François

DVDFab 8.1.8.1 (2012/05/13 14:20:10)

0m 01.45s: GPUAccelerate: 12351
0m 01.45s: CUDA cap: 0
0m 01.45s: Support coreavc decode: 0
0m 01.45s: Graphics info: NVIDIA NVS 3100M : 4.0 : 1.2
0m 01.45s: Qt Translator file load success
0m 01.49s: Load config successful.
0m 01.56s: Init profile data driver sucessful.
0m 03.57s: Init GPU settings sucessful.
0m 03.57s: option dvd2dvd 1 dvd2mobile 1 bluray2bluray 1 bd2mobile 1 bd23d 1 bd2dvd 1 file2dvd 1 file2bluray 1 file2mobile 1 filemover 1
0m 03.58s: dvd2dvd:dvd2mobile:blu-ray2blu-ray:blu-ray2mobile:blu-ray23d:blu-ray2dvd:file2mobile:file2dvd:file2bluray:
0m 03.79s: Config ExBar successful.
0m 03.79s: dvd2dvd have 8 elements.
0m 03.91s: dvd2mobile have 29 elements.
0m 04.68s: blu-ray2blu-ray have 4 elements.
0m 04.71s: blu-ray2mobile have 18 elements.
0m 05.18s: blu-ray23d have 7 elements.
0m 05.33s: blu-ray2dvd have 1 elements.
0m 05.36s: file2mobile have 28 elements.
0m 06.10s: file2dvd have 1 elements.
0m 06.13s: file2bluray have 1 elements.
0m 06.45s: Config work ui controls successful.
0m 06.64s: Init burn engine successful.
0m 06.67s: StartNotify successful.
0m 10.93s: info, try to open file G:/data/vid/test/test.mp4
0m 10.97s: info: open successed, iformat = QuickTime/MPEG-4/Motion JPEG 2000 format
0m 10.97s: info: get file-type(mov,mp4,m4a,3gp,3g2,mj2), which is not in media format list
0m 11.53s: 513.05 : video codec(28,828601953) try to connect inter-codec failed
0m 42.91s: Zhuo.Jia >> : WorkAttr::Init: HÃŽ
0m 42.95s: Zhuo.Jia >> : WorkAttr::Init OK: ìIç
0m 43.00s: info: prepare convert data for clip(00000.m2ts)
0m 43.00s: info: convert profile(m2ts.ac3.fast)
0m 43.00s: info: file (.mp4),3D(0)
0m 43.00s: info: streams((0.2)(1.2))
0m 43.02s: warning: request encode bitrate too big(756708 > 35000).
0m 43.02s:

info: convert work begin for clip(00000.m2ts)
0m 43.03s: info: set output video frame_rate(24000/1001)
0m 43.03s: try to use gpu acceleration(1) for video decoding
0m 43.03s: CUDA GPU acceleration for video decoding enabled
0m 43.03s: CUDA GPU acceleration for video encoding enabled
0m 43.03s: info: h264_encode: encode param profile(2) level(41) bitrate(35000)
0m 48.77s: error: filter name(filter_vdecode), type(2), id(1), get module_error(502.04 7 706 13)
0m 52.42s: info: convert work failed(504.00 0 error: filter name(filter_vdecode), type(2), id(1), get module_error(502.04 7 706 13)

) for clip(00000.m2ts)