EPIC not being backed up, hangs

[broderp]

I am trying to backup the movie EPIC.

DVDFAB9 claims "Analyzing completed sucessfully" then states "Copy Process started"

However, the Task Schedule bar stops at 99% (from the analyzing part) and it locks from there.

It doesn't even appear to be spinning the disc, and there are no lights going on on the drive(s)

I have tried two different BD drives with the same results. I have had no issues with any other disc.

I can post any logs if someone can tell me where to find them.

[CBR929]

Hi broderp
You will find the internal log here, see pic...
Also try the latest version of Fab found here http://forum.dvdfab.cn/showthread.php?t=24940
CBR929

[broderp]

I updated as you stated, and now it hangs when reading the disk.

I get a new window that says something about making a selection in like 30 seconds or the window will close.

Which log do you need to see?

[broderp]

There were several logs so I deleted them so I would capture the current log. I restarted the PC then tried to copy EPIC as I normally do.

The process has again hanged up on the analyzing stage (99%), yet it says the copy process has started as well as tells me the video reencode bitrate and Intel GPU acceleration for lighting-shrin..(cut off)

The process stops counting at 4:44 on the clock (and has been sitting there running like this for 1/2 hour with no change.

I copied what logs it made below:

"fab_burn.log"
this log is empty


"dvdfab_internal.log"
3m 47.00s: UILog:OnMsgToolbar_Start
3m 47.00s: UILog:Msg Start : ready start
3m 47.00s: UILog:Msg Start : start test run work
3m 47.00s: UILog:right button to null, work falg = -1
3m 47.01s: UILog:Msg Start : run work
3m 47.01s: UILog:Run current Work.
3m 52.40s: UILog:Begin work copy or converter.
3m 52.40s: UILog:start running at thread.
3m 52.40s: UILog:return flag at start running at thread ok.
3m 52.45s: BD MainMovie watermark flag: 0
3m 52.45s: UILog:MsgWork:WorkStatus_Start
8m 37.37s: Blu-ray Copy: Main Movie
8m 37.37s: Source: E:/BDMV/
8m 37.38s: Playlist: 800
8m 37.38s: Chapters: 1 -> 29
8m 37.38s: TotalSize: 28808 MB
8m 37.38s: SourceSize: 25840 MB
8m 37.38s: RemoveHDAudio: 0
8m 37.38s: CompressToAC3: 0
8m 37.38s: OutputSize: 23000 MB
8m 37.38s: OutputDisc: BDMV
8m 37.38s: OutputTarget: BD25
8m 37.38s: OutputVideo: 1080p/i
8m 37.38s: info: enable bd copy(mode=1)
8m 37.38s: info: estimate copied other streams size(4350 MB), estimate output video size(18419 MB)
8m 37.38s: info: video encode mode(0), bitrate(24062), lr-encode(no)
8m 37.38s: info: streams(4113.2,4352.1,4353.1,4608.1)
8m 37.38s: info: blu-ray copy begin (unit[elem[atomic[00600.m2ts],atomic[00601.m2ts],atomic[00602.m2ts]]])
8m 37.38s: Intel GPU acceleration for Lightning-Shrink enabled
8m 37.39s: info: h264_encode: encode param profile(2) level(41) bitrate(24062) crf(-1)


Also note that attempting to cancel the entire operation and close the program results in a spinning circle and eventually if you try to close a white screen, that I have to force close.

[CBR929]

Hi broderp
Please disable Cuda and Lightning Shrink and try again.
CBR929

[broderp]

No joy.

It appears DVDFAB is having an issue with reading the disc. I keep getting a read disc error.

I unselected Lightning shrink (I wasn't using Cuda) and the same thing.

The disk is clean (it is new) and I did a test burn of GRAVITY and it was fine. With Lightning Shrink enabled, it backed up Gravity to my HDD in about 40 minutes.