Convert flv to iPad.h264

[think1]

If I use the DXVA A/V Codec for H.264 it fails immediately.

If I switch the H.264 Video Decoder to "Software" it completes the conversion and the video looks fine but the audio is sped way up and completes in about half the time that the video does.

Are there some other settings I should change?

dvdfab_process

Conversion: one pass: 11:08:52
DXVA GPU acceleration for video decoding enabled
: 11:08:52
Work 1 failed, Error = 504.00 0 error: filter name(503.01), type(2), id(1), get module_error(502.04 7 705 9)

: 11:09:11

dvdfab_internal


25m 01.66s:


------ begin mobile work(1/1) ------


25m 01.66s: info: create config(3)
25m 01.67s: info: convert profile(iPad.h264)
25m 01.67s: info: file (.flv),3D(0)
25m 01.67s: info: streams((0.2)(1.2))
25m 03.79s: info: not set correct fourcc for video(28)
25m 03.79s: info: set output video frame_rate(30/1)
25m 03.79s: try to use gpu acceleration(2) for video decoding
25m 03.79s: DXVA GPU acceleration for video decoding enabled
25m 04.82s: info: h264_encode: encode param profile(0) level(30) bitrate(840)
25m 17.20s: error: filter name(503.01), type(2), id(1), get module_error(502.04 7 705 9)
25m 23.04s: ------ mobile work failed(504.00 0 error: filter name(503.01), type(2), id(1), get module_error(502.04 7 705 9)

) ------
26m 36.03s:


------ begin mobile work(1/1) ------


26m 36.03s: info: create config(3)
26m 36.03s: info: convert profile(iPad.h264)
26m 36.04s: info: file (.flv),3D(0)
26m 36.04s: info: streams((0.2)(1.2))
26m 37.92s: info: not set correct fourcc for video(28)
26m 37.92s: info: set output video frame_rate(30/1)
26m 37.93s: info: enable multi-thread software decoder
26m 38.95s: info: h264_encode: encode param profile(0) level(30) bitrate(840)
27m 45.94s:


------ finish mobile work ------

[think1]

Are there any other pieces of information I need to provide to help resolve this problem? Thank you.

[CBR929]

Hi think1
I will test this later when I get a chance.
Also were the .flv files made with Fab?
My suggestion would be to keep everything set to software.
CBR929

[CBR929]

Hi think1
I have tested this and received 504 error using 8226.
I then tested it using 9022 and it completed successfully, give version 9 a try.

8226
0m 53.81s: info: create config(3)
0m 53.81s: info: convert profile(iPad.h264)
0m 53.81s: info: file (.flv),3D(0)
0m 53.81s: info: streams((0.2)(1.2))
0m 57.66s: info: not set correct fourcc for video(28)
0m 57.66s: info: set output video frame_rate(25/1)
0m 58.96s: info: h264_encode: encode param profile(0) level(30) bitrate(648)
1m 13.11s: error: filter name(native_mux), type(128), id(12), get module_error(502.14 13)
1m 16.02s: audio_decode finish job
1m 18.02s: ------ mobile work failed(504.00 0 error: filter name(native_mux), type(128), id(12), get module_error(502.14 13)

9022
3m 40.51s: info: create config(3)
3m 40.51s: info: convert profile(iPad.h264.multichannel)
3m 40.51s: info: file (.flv),3D(0)
3m 40.51s: info: streams((0.2)(1.2))
3m 40.64s: info: not set correct fourcc for video(28)
3m 40.64s: info: perset file config OK !
3m 40.64s: info: set output video frame_rate(25/1)
3m 40.65s: info: SubMode(1)
3m 42.20s: info: h264_encode: encode param profile(1) level(31) bitrate(648)
4m 07.46s: audio_decode finish job
4m 37.76s:

Hope this helps
CBR929