DVDFab doesn't read from source DVD

[rona0628]

While I insert the media into DVD drive (E), pop up windows "open drive source E: xxxx" shows up for a 2,3 seconds and leaves the source
empty. FYI, the DVD media is not protected.

Here is the log.

DVDFab 9.0.1.6 (2012/12/31 01:03:50)

0m 00.43s: GPUAccelerate: 12351
0m 00.44s: CUDA cap: 1
0m 00.44s: Support coreavc decode: 0
0m 00.44s: Graphics info: NVIDIA GeForce GT 540M : 3.20 : 2.1
0m 00.45s: Qt Translator file load success
0m 00.62s: Start get sys number.
0m 00.62s: Serial number is: f0-bf-97-63-32-3d
0m 00.62s: Reg URL link is:
0m 00.62s: Version is: 9016
0m 00.62s: Product is: 2
0m 00.62s: Connect type is: 0
0m 02.39s: Times of connecting error is: 0
0m 02.40s: Parse string is: 2:1389052290
0m 02.43s: Parse string is: 20:1392834069
0m 02.43s: Parse string is: 21:1392834069
0m 02.44s: Parse string is: 22:1392834069
0m 02.45s: Parse string is: 60:1392834069
0m 02.45s: Parse string is: OV:9016
0m 02.45s: Parse string is: BV:
0m 02.45s: Parse string is: S:ef3160b2e54240f95ae637afa5455f71
0m 02.65s: End check info.
0m 02.65s: Load config successful.
0m 03.15s: Init profile data driver sucessful.
0m 03.27s: Init GPU settings sucessful.
0m 03.27s: option dvd2dvd 1 dvd2mobile 1 bluray2bluray 1 bd2mobile 1 bd23d 1 bd2dvd 1 file2dvd 1 file2bluray 1 file2mobile 1 filemover 1
0m 03.27s: dvd2dvd:dvd2mobile:blu-ray2blu-ray:blu-ray2mobile:blu-ray23d:blu-ray2dvd:file2mobile:file2dvd:file2bluray:
0m 12.28s: Init burn engine successful.
0m 12.43s: opening drive E
0m 12.44s: opened i/o
0m 12.45s: got media type 4
0m 15.36s: got max lba 2189279
0m 15.38s: got disc type 10
0m 15.46s: type DVD-VIDEO
0m 15.47s: volume label XXX_XX
0m 15.60s: failed to report agid: sensekey 00 asc 00 acsq 00
0m 15.84s: failed to report agid: sensekey 00 asc 00 acsq 00
0m 16.09s: failed to report agid: sensekey 00 asc 00 acsq 00
0m 16.30s: failed to open 200

[CBR929]

Hi rona0628
Please try the latest version found here
or even the latest of version 8 here

You may have to disable path player in Fab settings since there is no protection on the disc, just remember to put it back to always enabled.
Hope this helps
CBR929

Edit: You can also install ImgBurn to copy the disc to your Hdd and then burn to disc using ImgBurn since there is no protection on the disc.

[rona0628]

Thanks for your reply.
I've tried with 9.0.1.8 and 8.2.2.6 but with no change.
I've also disabled path player but it doesn't work.


Regards,
rona0628

[bustervegas]

dvd not protected

HI

Looks like you are trying to copy an unprotected dvd. You should go to the 8 fab version and check on the green check mark in upper right hand corner. Then go down on the left to protection and click on the dvd section under protection. Uncheck all of the protection features. Believe it will then copy your unprotected disk. Be sure to recheck those features for future use.
Good luck
Buster

[rona0628]

Hi

I tried with unchecked all of the protections options but with no luck.

rona0628

[maineman]

Is this a previously decrypted disc or simply an unprotected disc?
I'm asking because I suspect the authoring process used to make this "unprotected" disc does not conform to standard dvd structure
Translattion...Fab will most likely fail.

In any event, Fab should have no issues handling a previously decrypted disc, but it is nevertheless, overkill.
Why attempt to decrypt an unprotected disc?

Will the disc play in your pc or dvd player?

This is a shot in the dark, but you could try to open and burn a disc in Write Data mode. I doubt it'll open though.

I'm just guessing here since I have no clue as to the source disc, but I'd use other software such as nero, etc. or try Img if it's dvd compliant.

[fengtao]

Is't an external drive? If so, please try to connect to PC directly without USB hub, also you can try to upgrade the drive enclosure firmware if there is.