StreamFab for Windows 'Processing' takes stage significantly longer on 6030

[MrGrackle]

The post-processing stage probably takes 10 times longer (or more) now than with using 6029 and before. The progress bar crawls, then it hangs at around 50% for a considerable amount of time.
If I were to get a video before, it used to be almost instantaneous from processing to remuxxing. Not anymore. Every download seems to have "Download error: Md5 inconsistent" in the log itself. Not sure if that is related or not, or if that even matters. The attached log shows downloads from two providers.
I deleted the miles and miles of stuff at the beginning of the log that have no correlation.

[MrGrackle]

Meant to say 6230. Also, the download time is significantly longer too, all providers.
6229 on average downloads at 100MB/s. 6229 might go as high as 40MB/s.

[Stan001]

Something is different, or at least it seems. On Amazon, things still come pretty fast, regarding download, but processing and then remuxing seems a bit slow, and streamfab seems to download video, then audio. Why not download them both at once? Another issue with Streafab on several providers it uses one thread (or what can also be known as simultaneous downloads or connections) to download, which makes its download slower when most providers support downloading using more than one.

I guess for now, it's back to 6229 when this occurs.

[Germania]

The progress bar crawls, then it hangs at around 50% for a considerable amount of time.

Same here

btw: Processing is slower with 6230 as with 6229 ..

3x [Log]: Download error: Md5 inconsistent.
is often seen in other logs - but never in mine with 6230
I see this in your log after dl - so perhaps the "Saving Task Queue"

> Also, the download time is significantly longer too, all providers

I can't download that fast - maybe that's why I can't see the difference
But on holidays the network traffic is significantly higher for the streamers


btw: Keyword slower
The (2nd) Analyzing before Downloading from Netflix is 12-13x slower
with last releases as with SF 6223

streamfab seems to download video, then audio.

and now dl first video then audio - with <6230 the other way around

[MrGrackle]

Same here



btw: Keyword slower
The (2nd) Analyzing before Downloading from Netflix is 12-13x slower
with last releases as with SF 6223

Peacock on 6229 comes down at about 300MB/s (yes, that's right, 300 MegaBYTES per second), on 6230 it's gimps at 45 - 50.
This is tested just now (the holiday).

[Sebastian001]

The crucial question will be. It was intentional that it would take longer, or is it a mistake :-)

[Stan001]

I don't know, I guess it's perspective, hardware, or other.
I went all the way back to 6221 and have not seen a big difference in downloading, processing, or remuxing speeds. Others may get different results.
Only one movie on Netflix was tested; other results with the same or other providers and different movies/shows may vary.
During the whole processing stage, stremfab.exe seems to be very busy, doing what is not known or obvious. Possibly decrypting the streams?
After which remux starts and ffmpeg kicks in, doing most of the work. Then, after ffmpeg, your movie file is ready.

[jpp72]

Peacock on 6229 comes down at about 300MB/s (yes, that's right, 300 MegaBYTES per second), on 6230 it's gimps at 45 - 50.
This is tested just now (the holiday).

300 MB/s must be an error. Unless you have 3 Gigabit fibre (which i have) with your computer being connected via ethernet and not wireless. The ethernet would also need to be connected to a 10 gigabit port both ways and you are downloading to a very good NVMe PCIe SSD.

All possible but whenever StreamFab downloads chunks, it doesn't do it efficiently so you cannot attain those speeds.

I suggest you install DU Meter, NetMeter Evo, NetWorx or NetSpeedMonitor so you can see the real speed and not what StreamFab is saying.

It happened before with Discovery+ when it was saying 165 MB/s when DU Meter was saying 60 MB/s.

Ok, back to radio silence for me.

[Stan001]

Lol, I thought 300MB/s was high. They just upgraded to 1.5 gig in my area, and I fully get 1.5 gig download using speed tests. Still have slow downloads with certain providers so it seems some providers have limitations, and again I go back to streamfab using one thread versus multi-thread when downloading. And I have seen programs that download audio and video at the same time, not one then the other. This made a big improvement in downloading.
Still can't see why streamfab64.exe seems to have CPU and disk drive spike activities and seems to be somewhat slow in processing, once that's done ffmpeg takes over and things speed up to get a final video file. I know nothing on my system is causing this as no other spikes happen with any program running while watching Task Manager.
But I doubt we will see this addressed by streamfab developer, but the developer has surprised me before, so it could happen.

I don't replace any files in streamfab install, just to see what happens. The few times I did, I never did see much improvement.

Seeing >here the discrepancy in file sizes really gets crazy. I do know I need to get back to watching DU meter to see if it corresponds to streamfab downloading speeds.

[Sebastian001]

I can only speak for RTL+ on this point; they fixed something there at some point. Since then, the display has shown the speed twice as fast as it actually was... It's possible that it's correct again now...

I don't know if Wi-Fi 6 is the same in the US as it is in Europe, but it makes it almost impossible to get 1 Gig of fiber to the device. You need Wi-Fi 7 with a 6 GHz network, or LAN, at best.

I think it's the processing that's freezing or doing something else... that's the biggest limitation at the moment.